1. 您好,歡迎光臨萊州聚峰機械有限公司網站! 主營自動攪拌車,攪拌一體車,自動上料攪拌車等各種規格的產品。

      自動上料攪拌車生產廠家

      點擊撥打服務熱線:4008791999

      您的位置:首頁 - 新聞中心 > 公司新聞 >

      自動上料攪拌車離合器掛檔不佳的排除方法

      發布時間:2022-12-21 來源:http://www.wj2ylpt.com/ 瀏覽量:

      概述:在駕駛自動上料攪拌車的時候司機們經常會遇到這樣的情況發生:當發動機怠速運轉時,離合器踏板已踩到底,但掛擋很困難,變速齒輪有強烈的撞
      在駕駛自動上料攪拌車的時候司機們經常會遇到這樣的情況發生:當發動機怠速運轉時,離合器踏板已踩到底,但掛擋很困難,變速齒輪有強烈的撞擊聲。勉強掛上擋后,尚未放松離合器踏板,自動上料攪拌車已行駛或熄火,就這一現象小編來為您分析原因。
      When driving the automatic feeding mixer, drivers often encounter such a situation: when the engine is idling, the clutch pedal has been pressed to the bottom, but it is difficult to shift gears, and the gear change gear has a strong impact sound. After reluctantly engaging the gear, the clutch pedal has not been released, and the automatic feeding mixer has driven or stalled. I will analyze the cause of this phenomenon for you.
      通過以下方法進行檢查:將離合器底蓋拆下,把變速器掛入空擋,離合器踩到底。然后,用起工具撥動從動盤。如能輕松撥轉,說明離合器分離良好;如撥不動,說明離合器分離不好。以下是總結的故障排除方法:
      Check by the following methods: remove the bottom cover of the clutch, put the transmission into neutral gear, and step the clutch to the bottom. Then, use the lifting tool to move the driven plate. If it can be easily rotated, it indicates that the clutch is well disengaged; If it cannot be turned, it indicates that the clutch is not well disengaged. The following troubleshooting methods are summarized:
      1、檢查自動上料攪拌車離合器踏板自由行程是否過大,并調整。
      1. Check whether the free stroke of the clutch pedal of the automatic feeding mixer is too large, and adjust it.
      2、檢查自動上料攪拌車分離杠桿高度是否一致、是否過低。在車下撥動分離撥叉,使自動上料攪拌車分離軸承前端靠在分離杠桿內端面上,轉動離合器一周進行查看,如果分離杠桿的內端能同時和分離軸承接觸不上,說明分離杠桿的高度不一致,需應進行調整。如果分離杠桿高度一致,仍然分離不好,就要檢查杠桿高度。將各分離杠桿調到同樣的高度,如果能分離,說明原來調整不當或是磨損過甚。分離杠桿調整之后,須重新調整離合器踏板的自由行程。
      2. Check whether the height of the release lever of the automatic feeding mixer is consistent and too low. Move the release fork under the vehicle to make the front end of the release bearing of the automatic feeding mixer lean against the inner end face of the release lever. Turn the clutch for a week to check. If the inner end of the release lever can not contact the release bearing at the same time, it indicates that the height of the release lever is inconsistent and needs to be adjusted. If the height of the release lever is consistent and the release is still not good, check the height of the lever. Adjust each release lever to the same height. If it can be separated, it indicates that the original adjustment is improper or the lever is too worn. After the release lever is adjusted, the free stroke of the clutch pedal must be readjusted.
      自動上料攪拌車
      3、如果上述調整正常后,就要拆下自動上料攪拌車離合器,檢查從動盤是否裝反、軸向移動是否困難、主從動盤有無翹曲、分離杠桿螺釘是否松動、浮動銷是否脫落。
      3. If the above adjustment is normal, remove the clutch of the automatic feeding mixer truck, and check whether the driven plate is installed reversely, whether it is difficult to move axially, whether the driven and driven plates are warped, whether the release lever screw is loose, and whether the floating pin falls off.
      4、對于新鉚的摩擦片的離合器,要檢查從動盤和摩擦片是否過厚。如果過厚,可在離合器蓋和飛輪之間加墊片。
      4. For the clutch of newly riveted friction plate, check whether the driven plate and friction plate are too thick. If it is too thick, add shims between the clutch cover and flywheel.
      5、對于自動上料攪拌車液壓傳動的離合器,除上述檢查外,還應檢查制動液是否缺少,管道是否滲漏并排出液壓系統內的空氣。
      5. For the hydraulic clutch of the automatic feeding mixer, in addition to the above inspections, check whether the brake fluid is lacking, whether the pipeline leaks, and exhaust the air in the hydraulic system.
      關于自動上料攪拌車離合器掛檔不佳的排除方法內容您了解了嗎?實際上還要提醒您,平日對其的維保工作不能停止,更多相關注意事項就來我們網站http://www.wj2ylpt.com咨詢吧!
      Have you understood the troubleshooting methods for the poor engagement of the clutch of the automatic feeding mixer? In fact, I also want to remind you that the maintenance work can not be stopped on weekdays, and more relevant precautions will come to our website http://www.wj2ylpt.com Consult!

      截屏,微信識別二維碼

      欧美人体视频一区二区三区_亚洲 欧美 另类 综合_日本XXXX视频在线观看_第1页